Products Description
The 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor are anti-pollution, anti-aging, good hydrophobicity, excellent cold resistance and heat resistance, especially suitable for high altitude area, cold area, wet area, salt fog area and heavy pollution area. And installation without open fire, especially suitable for petroleum, chemical, mining and other flammable and explosive places.
1.Product Introduction
The 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor has the advantages of small size, easy operation, rapid, no special tools, wide range of application and less product specifications. Compared with the heat-shrinkable cable accessories, it does not need to be heated by fire, and moving or bending after installation will not be as dangerous as the heat-shrinkable cable accessories. (Because the end of the cold-shrinkable cable depends on the elastic compression force). The 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor installed installation procedures from one end to the other side of the construction, the construction process cannot be changed, the process is very difficult to have a bubble will appear in the cable pipe, therefore the construction quality is higher, the construction of hot shrinkage is different, heat from one end to the other side, it is easy to result in uneven heating, which leads to the generation of air bubbles, seriously affect the construction quality.
The scope of use of the 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor is suitable for 12/20(24)kV, XLPE, rubber insulated Three Cores power cables. And the installation environment of the 1kV Cold Shrinkable Three Cores Termination Kit should be dust-free, with a temperature above 0℃, and a relative humidity of 75% or less. The 1kV Cold Shrinkable Three Cores Termination Kit Installation acceptance test standards and operation supervision shall be carried out in accordance with relevant regulations.
2.Product Parameter (Specification)
Technical Specification
Test Item | Parameters |
Wet Power Frequency Withstand Voltage Test (Outdoor) | 48kV(72kV)/1min |
Dry Power Frequency Withstand Voltage Test (Indoor) | 54kV(81kV)/5min |
Impact Pressure Test | 125kV 1.2/50μ+10times |
Partial Discharge Test | ≤10pc(1.73Uo) |
There are four common technical parameters for the 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor. As for our 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor, the Dry Power Frequency Withstand Voltage Test is 54kV(81kV)/5min. And the Impact Pressure Test is 125kV 1.2/50 μ+10times. And the Partial Discharge Test is ≤10pc(1.73Uo). These parameters of our 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor are qualified and excellent. So you can rest assured purchase, if you have specific parameter requirements, please contact our agents, we will help you as soon as we received your request.
3.Product Feature And Application
1.Full shrinkage automatic reset technology, installation without special tools, construction and installation is simple and quick;
2.No open flame, no heating, safe and reliable;
3.The cable body has persistent radial pressure, good sealing and waterproof, to ensure long-term reliable operation.
4.Product Details
The Material list /Specific contents of the 24kV Cold Shrinkable 3 Cores Termination Kits for Indoor
Item | Components | Unit | Single core | Three cores | Remark |
1 | Breakout | pc | - | 1 | |
2 | Terminal tube | pc | 1 | 3 | |
3 | Jacket tube | pc | 1 | 3 | |
4 | Sealing tube | pc | 1 | 3 | |
5 | Self-adhesive tape | roll | 1 | 1 | |
6 | Water-proof sealing mastic | bag | 1 | 1 | Only outdoor |
7 | Filling mastic | bag | 2 | 6 | |
8 | Constant force spring | pc | 1 | 2 | |
9 | Semi-conductive tape | roll | 1 | 1 | |
10 | Armour earth braid | pc | - | 1 | |
11 | Shiled earth braid | pc | 1 | 1 | |
12 | Silicone grease | bag | 1 | 1 | |
13 | PVC tape | roll | 1 | 2 | |
14 | Abrasive paper | pc | 2 | 3 | |
15 | Cleaning tissue | bag | 2 | 6 | |
16 | Glove | pair | 2 | 2 | |
17 | Measure tape | pc | 1 | 1 | |
18 | Knife | pc | 1 | 1 | |
19 | Cone | pc | - | 1 | |
20 | Installation instruction | pc | 1 | 1 |
5.Product Qualification
Cold shrinkage cable accessories is the use of elastomer materials (commonly used silicone rubber and ethylene propylene rubber) in the factory injection vulcanization molding, and then through expanding, lined with plastic spiral support to form a variety of cable accessories. During field installation, these preexpansion pieces are put on the treated cable ends or joints, and the plastic spiral strips (supports) of internal support are drawn out and pressed on the cable insulation to form cable accessories. Because it is at room temperature by elastic shrinkage force, rather than like heat shrinkage cable accessories to heat shrinkage with fire, so commonly known as cold shrinkage cable accessories. The product is waterproof, stress control, shielding, insulation in one, can be used in a variety of harsh environmental conditions for a long time. Widely used in Electric Power Industry, Petroleum Industry, Chemical Industry, Metallurgy, Railway, Port, Construction and other fields.
Packing&Delivery
1.Your inquiry will be replied within 24 hours.
2. We offer you professional service in fluent English.
3. Keep the mass production as the sample in high quality.
4. Freight forwarder: faster, safer, and convenient.
5. Quality: we have QC on each process,provide high quality products.
Any problem or needed please feel free let us know, we are glad to service for you.
We are factory, we can provide competitive price. And all the products will be shipped after quality inspection. Usually we quote within 24 hours after we get your inquiry. If you can not buy our product in your local area, we will ship a sample to you (Please contact our agent or send email to our mailbox).
Packing
Packaging Details:carton, wooden cases, woven bag, plastic bag then put on pallets
We usually use standard carton Wooden pallet packaging.Other packaging is based upon customer requirements
Delivery Dtalis:Within two weeks
Cooperative Client
Our cooperative client are all over the world and our products are very popular all over the world. Many products are exported to Russia, USA, Australia, Canada, South Africa, Kenya, Tanzania, Zambia, Brazil and Argentina. Chile, Southeast Asian countries and other international markets. With first-class technical ability and perfect pre-sale and after-sales service guarantee system, we have established a good reputation between enterprises and users.
FAQ
Q: Do you provide sample service?
A: Yes, we only provide samples and ask for one piece at a time. The freight should be borne by you.
Q: Do you support customized services？
A: Yes, we can customize the size and logo according to your needs. Please consult the customer service for the specific minimum order quantity.
Q: How is the Design & Engineering?
A: Experienced and skilled team of designers including CAD designers and 3D designers has the capacity to deliver outstanding designs for your project. If you require more complex engineering of structures such as overhead transmission and distribution lines design,we can also provide this service also designer fee .
Q: What's the payment term?
A: We accept T/T, L/C, West Union.
Q: What's the delivery time?
A: Usually within 7-15 days according to quantities
Q: What's the standard of package?
A: Export standard package or special package as the requirement of customers.
Q: What kind of product quality your factory offer?
A: Our products with both excellent quality and competitive price. And we offer free sample for your reference.
Q: What kind of certificate you have?
A: We have ISO9001:2008
